Fishing is a pleasurable activity. It can open doors to new and exciting adventures. Of course, the joy of catching a giant trophy is something worth looking forward to, as well.
However, you won’t be able to enjoy all of these if you don’t know how to use your fishing tools properly. Among the things that you should acquire is the skill of properly spooling a line to your reel.
How to put line on a reel? It is a question that many amateur anglers frequently ask. Despite being tricky in nature, putting a line of any types of reels (e.g. spinning and baitcasting) is a relatively easy task.
In fact, it is the first skill that you will inadvertently master. As long as you got a high-quality line, doing this task should not be troublesome.
Table of Contents
- 1 How to Put Line on a Reel: How to Do It Correctly
- 2 The Tension in the Line is Necessary
- 3 Conclusion
Regardless of the type of fishing reel that you have, spooling still follows one golden rule. Specifically, the right way to the spool is observing the line and how it comes off in the two ends of your spool supply.
1. The first thing that you should do is to look for the side that doesn’t coil too much. Next, you have to apply pressure on it before you spool it to your reel.
2. To start with the spooling process, you need to mount your reel on your fishing rod. After this, let your line pass through the guides of the rod. Most importantly, you should start at the tip of the rod.
If you are using a spinning reel, you have to loosen its bail so that you can tightly tie the line on its arbor. When it comes to knots, we recommend that you will do the Improved Clinch Knot.
3. Snip the excess ends with a scissor. Close the bail afterward.
4. Again, if you are using a spin casting reel, you should take out its hood. Next, pass your line through the hole in the hood and knot it to reel’s arbor. If you are using a baitcasting reel, take the line and pass it through the reel’s guide. Just like in the spin casting reel, you have to tie the line on the arbor and cut off any excess tags.
5. Next, put your supply spool on any flat surface (e.g. the floor). Specifically, the line should make a spiral motion when you put it from the supply.
6. If the line is already running on the guides or your rods, you should raise the latter’s tip four feet above the spool’s supply. Next, you have to turn the reel handle for at least twenty times. Check the line if there are any twists. You can do this by lessening the tension on the line.
7. Next, you have to lower the tip of the rod so that you can check for any twists on the line. If you can see coils, then you should put the spool supply in an upside down position. By doing this, you will remove the majority of the twists that you can see. After all, you are winding all of the lines toward the reel.
But if you can see that the other end has more twists and coils, you should return to the first end and remove the line while the supply spool is in an upward position. This method is the reverse of the previous process.
Alternatively, you could also insert a pencil or similar objects to the spool so that you can freely turn while you are spooling the line. However, you have to remember that this method is not as efficient as the method we mentioned. Specifically, putting a pencil in the spool works only on baitcasting reels. But for spin casting and spinning reels, it could cause problems.
When spooling a line, it is important to pay attention to the pressure that you apply. Applying a moderate amount of tension on the line is crucial, regardless of the type of reel that you are using.
You can do this by pressing the line between your forefinger and thumb (it should be your free hand).
After all, you have to realize that without sufficient tension, the line can overwrap. The worst part of this is that you might not notice this problem until you are out in the water already.
Therefore, we highly recommend that you always check the integrity of your spooling before going fishing.
Even if you are still a beginner, you should have no trouble learning them. As long as you follow these procedures correctly, you can guarantee that your fishing reel is firm and free from any curling!
Did you learn anything from this article? What are the other methods you know for spooling a line on the reel? Share it with us in the comment section below!